Engine Paint AMC Blue Aerosol 12 oz @ Tools, Equipment & Painting online store

Carb Renew - Restore the OEM look found on just about any carburetor. Carb Renew is a translucent acrylic enamel that isresistant to fuel and most additives. (Please read and follow label instructions carefully.) While your carburetor is apart and all jets are removed, simply spray Carb Renew on the exterior of the thoroughly cleaned bowl cover and main body. Produces a natural 3-8% gloss. Carb Renew is supplied in a 5 oz. net wt. aerosol can. Enough to cover 2 sq.ft. PRE Painting Prep (10041Z) can be used to clean the carburetor before coating.
SKU: 10179 Z
Category: Specialty Coatings Underhood Coatings Gas Tank Sealers & Fuel Systems

Grey Metallic is a hybred Epoxy/Polyester blend with a bondedmetallic additive to assure a uniform finish. Cures at 400 degrees F (204 degrees C) for 20 minutes after flow-out (that transition from dry powder to a liquid look) occurs. Produces a smooth 80-90% high gloss finish. May be topcoated with (10093) Gloss Clear or (10286) Super Gloss Clear for improved UV resistance, gloss and increased depth.
SKU: 10341 5LBS
Category: HotCoat Powder Coating Powders Specialty Colors

Silicone Plugs - This pack of 10 hightemp silicone plugs fit holes from 1/8"- 1/4". Plugs are reusable.
SKU: 58030
Category: HotCoat Powder Coating Powder Coating Equipment Powder Coating Accessories

HotCoat powders are exclusively formulated for this system. They are optimized to promote static charge for uniform coverage and finish. All are UV and fuel resistant. Packed in 8 oz. netweight cans. Coverage is equivalent to 2-3 aerosol cans (appromately 10-20 sq. ft.).
SKU: 10218
Category: HotCoat Powder Coating Powders Textured Colors

2 1/16"0-200 psi Z-Series oil press gauge(M)
SKU: 74312
Category: Auto Accessories and Gifts

This kit contains 1 Hood Decal, 1 Rear Deck Panel Decal, 1 Rear Spoiler Decal, squeegee and instructions. Multi-colored decals are red, white, blueand black.
SKU: 10665
Category: Styling, Care & Custom Phoenix Graphix Chevrolet

MAGNETO SHUTDOWN RELAY KIT #50104 - Since a magneto does not require battery power to operate, your engine may continue to run even with the battery disconnect switch turned off. Kit grounds the magneto'sinternal windings, preventing the coil from producing a spark. Easy to install with all hardware and instructions.
SKU: 60154
Category: Performance & Tune-Up Electrical & Diagnostic Relay Kits & Connectors

The beauty of stainless steel trim is that it does not pit or corrode, but over the years it can get scratched.This Kit can return this trim to like-new condition. Includes three Buffs (Sisal, Spiral Sewn, and Loose Section); three Buffing Compounds (17.75 oz. Emery, 17.75 oz. Stainless, and 16 oz. White Rouge); and 8 page instruction booklet. Will also work on non-stainless steel parts. Enough to buff the trim on most cars and trucks.
SKU: 13102
Category: Metal Buffing & Finishing Buffing Buffing Kits

Now you can customize your ride or your shop w/ style in minutes w/ these pre-machined sheets of.063" Aluminum or.030" Stainless Steel. Available in a variety of sizes ranging from 6"x12" to 36"x48" w/ turning diameters of: ø", õ", 1", 1-ø" & 2" to meet your specific fabricating needs. Whether you're working on aninstrument cluster housing, a radio bezel, some interior trim or an all-out firewall, Eastwood has you covered!
SKU: 28298
Category: Metal Shop Fabrication Accessories

Use on tools, electrical equipment,tool boxes and car parts. This styrenated alkyd copolymer is formulated with quality resins, glass, and aluminum particles carried in a quick-drying solvent to form a corrosion resistant, weather repelling barrier. Colors shown are approximate. Produces a smooth high gloss finish. Approx. 90% gloss. Covers 6 sq. ft. Withstands up to 250 degrees F. Buy 3 or more and SAVE!
SKU: 10164 Z
Category: Specialty Coatings Detail Coatings Miscellaneous Coatings

These cleverly-designed tools will take care of any problem areas that crop up towards the end of the painting process. Run Razor holds standard razor blades at a precise angle to shave down semi-hardened runs, sags or dust between color or clearcoats. Just pass it gently over the surface, dialing down the blade position indicator in.001" increments until the imperfection isgone. Run Blocker provdes three different contoured aluminum blocks that can be used with wet/dry sandpaper to finish runs that have been cut down with nib files. Can also be used for block sanding body filler or primer.
SKU: 34007
Category: Specialty Coatings Painting Paint Prep / Touch Up

Protection and piece of mind! Don't risk damage to that new chrome plating or powdered surface! Use this 140 piece set (1/8",11/64",3/16",1/4",11/32", 13/32",1/2"I.D.)under hardware to protect the surfaces. Washers are milky in color and can be trimmed (if necessary)to inconspicuously fit under bolt heads or metal washers. Prevent leaks, (use one on every oil change), and prevent vibration from loosening hardware.
SKU: 43191 G
Category: Shop Tools Hand Tools

Auto Air Metallic Colors may be used alone for a metal-like appearance or use as follows: Metallic Colorsare best used over Auto Air Base Coat Sealer Dark or 4200 Series Deep Black Graphic Colors. Use as a base for 4200 Series Transparent Graphic Colors for custom metallic blends, or as base for the 4600 Series Candy Colors. Metallic Colors? pigments are heavy and may require vigorous shaking, bottles may be left upside down for a few minutes before shaking.
SKU: 34437 001
Category: Auto Body Pinstriping / Airbrushing Airbrushing

Cosmic SparkleColors create a refined, star-like subtle shimmer effect. Cosmic Sparkle Colors have a more narrow size particle effect pigment then the Hot Rod Sparkle Colors. Cosmic Sparkle Colors are semi-translucent colors with a semi-gloss finish.Cosmic Sparkle Colors are best used over Auto Air Base Coat Sealer Dark or Auto Air 4200 Series Deep Black Graphic Colors Apply 1-2 light coats of Auto Air Base Coat Sealer Dark and 2-4 coats of Cosmic Sparkle Colors.
SKU: 34480 001
Category: Auto Body Water Based Paint

Supercoup NR1 Nibbler Shears Mini-Nibbler Cuts Metal Without Distortion - Compound leverage action makes cutting much easier than with snips. Starts in the middle of a panel with a 1/4" hole. Jaws are made from hardened steel and are replaceable in seconds. Cuts up to 22 gauge stainless, 18 gauge steel,.059" copper, brass,.079" PVC,.098" Ploycarbonate.Made in France.
SKU: 28191
Category: Metal Shop Fabrication Cutting

This standard 6" shaft length steel cutting carbide burr is designed for rapid material removalfor porting or grinding. 20,000 rpm max. Made in USA.
SKU: 46288
Category: Metal Buffing & Finishing Surface Conditioning Abrasive Rolls & Tapers

Waterproof Battery Tender - Maintain your 12-volt battery in peak condition. Extends battery life by 3-5 years. Specially designed to operate in wet, dry, hot, or cold conditions. Will not charge a dead battery. Great for maintaining batteries in cars and watercraft in storage. Input 100-240 vac, 50/60 Hz, Output 12 V dc @ 800 mA.3-year warranty.
SKU: 25092
Category: Performance & Tune-Up Electrical & Diagnostic Battery Kits

The Fluidizing Attachment slips onto the end of the longer tubethat goes inside the powder bottle. This attachment diverts the fluidizing air stream into a random pattern that more readily fluidizes the powder for improved mixing and flow.
SKU: 34128
Category: HotCoat Powder Coating Powder Coating Equipment Powder Coating Accessories

New or a classic, any Harley-Davidson motorcycle should be protected from extended exposure to dirt, heat, moisture, and ultraviolet rays. Covercraft's Custom-Fit Cover for Harley-Davidson motorcycles includes steel cable reinforced grommets, heat shield, soft liner at windshield and fender area, and a free storage bag! For "Sportster" Type Bikes, 883 & 1200 -- will accommodate all stock Sportster models.In Black Urethane.
SKU: CVHC154BU
Category: Styling, Care & Custom Car Care & Protection Motorcycle Covers

These handy blind holders are used by custom car builders to hold sheet metal parts before finalwelding. Very easy to use. Drill a 1/8" hole through both pieces and insert fastener. Each one provides nearly 20 lbs holding power and has a grip range of up to 1/4". A side-grip fastener is included for edge work. For panels with flanged edges, use the C-panel holders.
SKU: 19074
Category: Tools & Equipment Shop Tools Body & Fender Tools

Eastwood's yellow ultra-high-molecular-weightplastic mallets stretch and form sheet metal. Screw secured head captures handle within for proper fit and allow the head top to be used for forming. Made in the USA.
SKU: 28114
Category: Metal Shop Fabrication Forming

A unique push or pull cutting; can turn or rotate while cutting circles. Provides easier cuttingin tight spaces and overhead. Elevates hands above metal working surfaces. Faster, easier and safer cutting for improved productivity. Cuts up to 24 gauge sheet metal (26 gauge stainless steel).
SKU: 28357
Category: Tools & Equipment Shop Tools Body & Fender Tools

Eliminate glare andangle your gauges towards you, the driver. Quality molded black plastic rings come three to a package. For all AutoMeter and Autogage 2-1/16" gauges.
SKU: 74172
Category: Performance & Tune-Up AutoMeter

Painting can cause static charge to build that willl actually cause dust particles in the air to be attracted to your nice fresh finish! Help prevent this by grounding the chassis of the vehicle you're painting and wearing an Anti Static Suit. This lint free fabric is interwoven with electro conductive carbon fiber to provide the utmost in protection and comfort. Innovative fabric reduces heat build up so you canwork in comfort. Separate hood. Velcro cuff closures. Extremely light weight.
SKU: 34295
Category: Auto Body Painting Paint Guns

Want to find out what lies below the paint? Locate body repairs and measure total film thickness from 0-.040" on steel bodied cars. Built in contact makes it easyto scan the surface to pinpoint body damage
SKU: 34290
Category: Auto Body Body & Fender Body Tools & Accessories

Safety and versatility are two key design features of this polypropylene housing barrel pump. This, combined with the Ryton vanes gives this pump the ability to transfer petroleumbased products, antifreeze, and a variety of water based alkali and acid based solutions. Three piece extension tube has a built in filter and the included bung fitting adapts pump to standard 2 inch barrel threaded fitting.
SKU: 10367
Category: Tools & Equipment Shop Tools Unique Tools

For All 2-5/8" Auto gage& Auto Meter gauges, 3-Hole Black Aluminum Panel.
SKU: 74392
Category: Auto Accessories and Gifts

Auto Air Fluorescent Colors are transparent neons with a semi-gloss finish. Use over Base Coat Sealer White or a light background Semi-Opaque orTransparent Color for dramatic neon effects.
SKU: 34389 001
Category: Auto Body Pinstriping / Airbrushing Airbrushing

This kit includes the 3/4 HP motor at 1800 RPM, 6 compounds, 2 each of the10"buffs with 3/4" hole, face shield, dust mask, gloves, buffing instructions and "The Art of Buffing" video.
SKU: 13024
Category: Metal Buffing & Finishing Buffing Motors / Accessories

Enhance Your Performance.Kit contains two performance deflectors for enhanced tranfer efficiency of powder, a fluidizing adapter for uniform mixing of different powders, and three gun cups with lids for quick color changes.
SKU: 10186
Category: HotCoat Powder Coating Powder Coating Equipment Powder Coating Accessories

Eliminate irritating shield flipping. Now you can see exactly where you are at all times and concentrate on the work. A photocell senses the lightfrom the arc and dims the liquid crystal lens in a blazingly quick 0.025 milli- seconds. It lightens just as quickly when you stop. Shade adjusts from #9 to #12 and sensitivity can be set to suit lighting conditions. This Helmet has a 2.75 clear shade for much easier viewing. Shut off is automatic after 30 minutes at idle. Helmets use two AAA batteries (included) and feature a low battery warning light.
SKU: 19100
Category: Metal Shop Welding Welding Helmets

Full size heavy duty shop drill press features a rugged 3/4hp motor and adjusts to 16 speeds varying from 195 to 3630 RPM. Full 5/8 inch capacity chuck and 30 inch maximum reach from spindle to table make for great versatility. Features cast iron base and table, precise rack and pinion vertical adjustment, a table that rotates a full 360 degrees and pivotsup to 45 degrees, and a quick release tension lever for rapid speed changeovers.
SKU: 10317
Category: Tools & Equipment Shop Tools Unique Tools

The tough durable coating that seals and protects! Increase resale value, reduce maintenance and add a detailed look. Drop in liners can warp and trap water and contaminants that lead to bed corrosion. This two part epoxy is easy to apply with a wide brush, roller or sprayed with Undercoating Gun (16030A).Cured finish is flexible at low temperatures, offers a non-skid chip resistant finish. Adheres to firmly adhereing paint or bare metal. Degrease area to be coated and mask. One kit covers 32 square feet. Most truck beds require 2 kits. 2 or more kits are available at a discounted price.
SKU: 10129 Z
Category: Specialty Coatings Detail Coatings Truckbed Liners

Extend the life of mechanical components by assuring complete and proper lubrication. The adapters included in this kit are used with your manual or powered grease gun. Kit includes needle adapter, whip hose w/hd coupler and quick disconnect, recessed lube adapter w/quick disconnect, rubber tipped seal off dispencer w/quick disconnect, 1.5" narrow needle adapter w/quick disconnect, right angle adapter w/quick disconnect, 90 degree adapter w/quick disconnect.Imported. One year manufacturer's warranty.
SKU: 49144
Category: Performance & Tune-Up Drivetrain Engine Tools

2-1/16" 0-1600F Z-Series E.G.T. Pyrometer Kit(E)
SKU: 74342
Category: Performance & Tune-Up AutoMeter Z-Series

The more advanced Series of Paintucation videos (34139) includes Body Shop Basics, Metal Prep/Rust Repair, Paint Your Car, and Color Sanding/Buffingat a savings.
SKU: 34139
Category: Metal Buffing & Finishing Buffing Books & Videos

Console pod for your 1968-69 Camaro or 1968-74 Chevy Nova. Mounts four 2 1/16" gauges in the factory shifter console. Pods are molded using a durable ABS plastic that can be paintedto match the stock interior. Not a cheap imitation!
SKU: 75094
Category: Performance & Tune-Up AutoMeter Pods

These Pro-Comp electric gauges are the perfect choice for professional applications where wiring is preferred to steel braided lines and tubing. The clean look matches the style and appearance of the popular liquid filled mechanical gauges. Pro-Comp electric gauges contain a serious air core movement for the very finest in operation and accuracy! THis Oil Pressure gauge reads 0-100 PSI and includes 1/8"electric sender & 1/4" NPT fitting.
SKU: 74898
Category: Performance & Tune-Up AutoMeter Pro-Comp

Auto Meter's American Platinum series offers a brand new look for your street rod. The clean, brushed, aluminum dial face and black nickel bezel create a classy and unique style. This is accented by an aggressive number style and pointer for a powerful look. Also included are red and green colored light bulb covers fora custom night-driving look.
SKU: 74137
Category: Performance & Tune-Up AutoMeter Street Rod

This kit is for a 1983-87 Shelby Charger and contains FrontBumper, Fender, Door and Rear Quarter Panel Stripes Kit ('Turbos' sold separately), squeegee and instructions. Decal color is silver.
SKU: 10813
Category: Styling, Care & Custom Phoenix Graphix Dodge

Electric gauges provide a no-nonsense installation and are the perfect choice to be used with Gauge Works mountingaccessories. Includes 1/8" electric sender & 1/4" NPT fitting.
SKU: 74981
Category: Performance & Tune-Up AutoMeter Phantom

Watch steel braided lines and copper tubing disappear before your eyes! Phantom electric gauges feature advanced internal components for the ultimate in accuracy and smooth pointer movement. Electric gauges provide a no-nonsense installation and are the perfect choiceto be used with Gauge Works mounting accessories. Includes electric sender.
SKU: 74951
Category: Auto Accessories and Gifts

Super-hard carbide burrs used in a high-speed die grinder can really make a tough job easier. Grind weld beads, shape parts, smooth rough castings, port cylinder heads. All burrs have a 1/4" dia. shank. Burrsets include: cylinder, pointed tree shaped and round nose. Individual burrs are available separately. Use these above burrs for Steel and Iron. Use (46060) 6" Tree Shaped Burr for Aluminum.
SKU: 46058
Category: Performance & Tune-Up Drivetrain Porting & Grinding

These270deg "full sweep" gauges feature a quality engineered bourdon tube design and durable, performance grade movements for unsurpassed accuracy under the most demanding conditions. Includes 6 ft. sender line.
SKU: 74943
Category: Performance & Tune-Up AutoMeter Phantom

Smoothes away scratches faster than standard sisal wheels. Combines the aggressiveness of sisal with the coloring capabilities of cotton sheeting. These materials are sewn together at a standard spacing and held together in a metal clinch ring. The unique construction of this buff allows for flexibility, andthe "open" face provides a cooler surface than a full-disk buff. Use with 13134 Emery Compound or 13129, 13194, 13131, 13132 Greaseless Compound
SKU: 13429
Category: Other Ways to Shop Eastwood Branded Products

Nu-Tecsys PlasmaCutter Replacement Nozzle
SKU: 19116 A
Category: Metal Shop Welding Plasma Cutters

Underlift stabilizing stands are valuable tools for positioning and stabilizing engine and drivetrainassemblies. Ideal for performing shock absorber and exhaust work. Unique foot pedal operation provides instant height correction in the range of one inch. Full 1,650lb capacity with a support range from 54-1/2 to 80-1/2 inches. 21 inch round base dimension.
SKU: 10246
Category: Tools & Equipment Shop Tools Unique Tools

Pro-Comp electric gauges are the perfect choice for professional applications where wiring is preferred to steel braided lines and copper tubing. The clean look matches the style and appearance of the popular liquid filled mechanical gauges. Precision air core movement eliminates friction for the very finest in operation and accuracy!
SKU: 74909
Category: Performance & Tune-Up AutoMeter Pro-Comp

Pro-Comp electric gaugesare the perfect choice for professional applications where wiring is preferred to steel braided lines and copper tubing. The clean look matches the style and appearance of the popular liquid filled mechanical gauges. Precision air core movement eliminates friction for the very finest in operation and accuracy! See Item No. 75020 for digital voltmeter option.
SKU: 74920
Category: Performance & Tune-Up AutoMeter Pro-Comp

2-1/16" Dual Pod Eclipse 1995-98 CarbonFiber
SKU: 75368
Category: Performance & Tune-Up AutoMeter Pods

Satin Black Exhaust Detailing Kit - 1 each of Satin Black High Temp Coating Exhaust Paint aerosol (10020Z) and a Pack of 3 disposable foambrushes (34152).
SKU: 10183 Z
Category: Specialty Coatings Underhood Coatings High Temp / Exhaust Systems

Car Sander- Shaped like a funny car, this comfortable sander will inspire you to "block-out" primer even faster. Working face 7-3/4" long by 2-3/4" wide.
SKU: 11291
Category: Rust Treatment Rust Removal Mechanical Rust Removal

Stop Using Wire Brushes. Sick of discovering wire bristles in your favorite sweatshirt? Now there is a better, longer lasting, safer alternative. The 3-M Radial Bristle Brush is made from a plastic like material that's uniformly impregnated with abrasive. As the wheel wears, fresh abrasive is exposed to assure consistent cutting action. Includes push-out sleeve adapters to fit motor shafts from 1/2" to 1". Six inch diameter 8 ply wheel with 1/2" face Maximum RPM 10,000, Green (50 Grit). Great forremoving rust and old finishes
SKU: 31176
Category: Metal Buffing & Finishing Surface Conditioning Bristle Products

When superior atomization and build quality are of the highest importance - Demanding Professionals Demand Sata. This gun canbe used to apply heavy primers to color and clear coats. The Sata Mini Jet 4 HVLP gun includes instructions, a 1.0mm nozzle set with special air cap for finer atomization (needed for spot repairs) and aluminum 150 cc cup (about 5 ounces). Requires 3.6 cfm at 29psi. All guns are backed by a 1-year limited Manufacturer's warranty.
SKU: 11218
Category: Tools & Equipment Shop Tools Body & Fender Tools